CAR TALK

DEAR CAR TALK: I have a 1988 Chrysler LeBaron convertible. I had a remanufactured 2.5-liter engine installed. The engine vibrates. The engine and transmission mounts were replaced, and the vibration is worse; I can really feel it in the steering wheel. The dealership said the shop that installed the engine might not have reset the timing in the two balance shafts. In addition to that, what else would cause the engine vibration?

-- Lin

DEAR LIN: Wow. An '88 Chrysler LeBaron. I just had a Ricardo Montalban flashback.

I'd suggest that you go back to the shop that installed the engine and have them figure this out for you, Lin. Since you bought a remanufactured engine rather than a used engine, it should perform like a new engine. Certainly, it shouldn't be shaking the car enough for your hands to look blurry when they're on the steering wheel.

If you came to my shop with this problem, the first thing I'd do is check your compression. Actually, the first thing I'd check is your credit limit. But after that, I'd make sure that the compression is good in all four of your cylinders. If one cylinder has low compression, you'd essentially be running on 3 1/2 cylinders. That definitely would cause the engine to shake.

Another thing I'd check for is a vacuum leak. It's not unusual, when you remove and replace an engine, to accidentally crimp a vacuum hose or forget to reattach one. A vacuum leak also would cause the engine to run roughly and shake.

On modern cars, a vacuum leak would turn on the Check Engine light and set a code. But your car's so old that the Check Engine light's probably been on since 1991.

There is a balance shaft in this car that's run by one of the timing belts. If that belt is off by just one tooth, the balance shaft will be out of sync, and it won't be able to do its job and dampen the vibrations.

Unfortunately, the only way to check that is to remove the front covers of the engine, remove the timing belt and start over ... lining up the belt and the timing marks from scratch.

If it turns out the valve timing is the cause of the shaking, then the remanufacturer really should bear the cost of the repair. The valve timing is set at the factory, before the engine is shipped, so your installer would not be at fault there.

But if he's a good guy, he'll call the remanufacturer on your behalf, explain the situation and make arrangements for the remanufacturer to pay him for the repair -- letting you off the hook.

And, obviously, if the engine compression is low, that's the remanufacturer's fault, too. But in that case, the engine's going to have to go back to the factory ... for re-remanufacturing. Good luck, Lin.

DEAR CAR TALK: I bought my 2000 Honda Civic off the dealer's showroom floor and have kept the car maintained faithfully. The car now has 265,000 miles on it, with the original engine and clutch, and still runs great. I think rust will kill it before the engine stops, but for the past year, the clutch seems to catch only at the very top when I release it. It's been getting tricky to give it enough gas at the right time without shuddering, from the stop position.

I've had my mechanic look at it a couple of times, but he can't find anything wrong with it. I don't know if it's a stretched cable or simply time to replace the clutch or parts of it. I really don't want to get stranded. Do you have any suggestions?

-- Tom

DEAR TOM: After a mere 265,000 miles, you need a clutch. The time has come. The average person gets 75,000 or 100,000 miles out of a clutch. If you're doing lots of highway driving, where you're not shifting very much, you sometimes can do quite a bit better than that. But 265,000 is at the far end of the bell curve -- off the page, actually.

So, be grateful that you got three times as many miles as most people get from a clutch, and if you think you can keep the rust at bay for a couple of more years, spend the $700 and put in a new clutch.

This is a hydraulic clutch, and it's self adjusting. So, as the clutch disc wears down, the clutch pedal automatically adjusts the engagement point, to keep it where it's supposed to be.

The problem is, you've run out of adjustment: There's no more clutch left to adjust. The telltale signs are that the engagement point is all the way at the top, and the engagement range is very narrow, making it hard to engage without chattering.

On the bright side, with the engagement point that high, if the floor under the front seats rusts out, pretty soon you'll be able to drive from the back seat. Good luck, Tom.

Ray Magliozzi dispenses advice about cars in Car Talk every Saturday. Email him by visiting

cartalk.com

HomeStyle on 05/16/2015

Upcoming Events